It is not hard to visualize the pain you are experiencing while your toilet is not functioning in the way it should be, and even though you could right away call up an expert, that’s not the only solution.
Besides, professional assistance can sometimes be pretty expensive, and it’s no point paying for something you can fix on your own with just a bit of time and effort.
This post will address one of the most common toilet issues, and it is declined flush power. There are times when just a single flush doesn’t do the work, and as the problem gets consistent, it’s a clear indication of something wrong with the flush system. However, there are ways to resolve this problem. This will take a bit of trial and error.
However, this will most likely solve the problem unless something is seriously wrong with the toilet and need a professional solution. We tried keeping our steps very simple for your convenience, and the ways that we are going to discuss in this post aren’t difficult to follow. Let’s jump in.
It Might Be Helpful:
- Methods Of Unclogging Toilet Without Plunger
- How to Use Toilet Seat Cover Properly?
- How to Stop a Toilet Overflowing?
Check if the toilet is clogged
Even a smaller obstruction can slow down your flush. The simple way to check this is by pouring a gallon of water into the toilet and flush it. If the flush isn’t the same as before, there is a high chance that your toilet is clogged somewhere.
You could use a plunger to unclog it. In most cases, this should fix the problem, but if it doesn’t bring any change, you could consider trying our next technique.
Toilet tank fill line level and adjustments
The next best thing to do is removing the lid of the toilet tank and checking if the water level is normal, i.e., at the designated line or, in other words, one inch below the overflow tube. If it is not and the water level is low, you must try adjusting the tank float assembly to raise the water level.
In the case of a ball float, you could raise the water level by turning the fill top screw clockwise, and in case of a cylinder float, you could squeeze the float’s clip and then pull the float up until it raises the water to the desired level.
Clean the bowl flush holes
The toilet bowl flush holes are located close to the rim, and sometimes, they get blocked. This will eventually weaken the flush power. Cleaning it can be challenging, but the best way to go about it is cleaning it using a bobby pin or a coat hanger wire.
As you do it, you have to check if this improves the flush power. If that doesn’t work either, don’t lose hope, and we still have a few more ways to go about it.
Try cleaning the toilet with bleach
Cleaning the toilet with bleach can be very effective. However, to do this, you must first shut off the water by turning the knob of the water supply valve that comes out of the floor or the wall.
Next, you could pour about one gallon of bleach in the bowl of the toilet and leave it for about 20 minutes, and this should clean up some blockages, thereby enhancing the flush power to some extent.
Using a vinegar soak
Using a vinegar soak in the toilet tank is another super effective way to resolve this problem. First off, you must open the toilet tank lid and then remove the fill hose. Next, you can use a funnel and fit it into the tube inside the toilet tank.
As far as the quantity of vinegar goes, you can use a quart of white vinegar and put it into the tube through the funnel. Leave it for 2 hours, and this should clean up the junk deposits from the toilet system.
Seeking an expert’s help
All the five steps discussed in this post aren’t hard to follow, and trying these steps should most likely resolve the problem for most of you. In fact, the cause of the problem can’t be anything other than what we have discussed in this post so far.
However, just in case you don’t see any improvements despite trying these techniques, it could be just that you haven’t been able to spot the blockage well, and in that case, you can, of course, seek an expert’s assistance.
Try our five easy steps, and you should not need professional assistance for sure
We are sure you have read this post carefully this far and understood the five steps mentioned in this post. In case you have any doubts, you can always go through the sections over again. You can also feel free to email us anytime just if you have any confusion, and we will be more than happy to help you.
To brush up your memory a bit, if you ever experienced a decline in the flash power, you can enhance the power of your flush by using a plunger to unblock any blockage inside the toilet, raising the water level in the tank, cleaning the bowl flush holes, cleaning the toilet with bleach, and using a vinegar soak in the toilet tank.
Leave a Reply